ELV Slide Dimmer Light Switch – Single Pole / 3-Way, Wall Plate Included, UL Listed

The ELV Slide Dimmer Light Switch delivers smooth, precise lighting control for modern LED and electronic low-voltage lighting systems. Designed with advanced reverse phase (trailing-edge) dimming technology, it ensures stable performance while reducing flicker and buzzing commonly found in standard dimmers.

Featuring a large slide control for precise brightness adjustment and an integrated rocker switch for quick on/off operation, this dimmer makes it easy to set the perfect lighting level for any environment. Compatible with both 120V residential and 277V commercial electrical systems, it supports a wide range of lighting applications. The included wall plate provides a clean and professional finish after installation.

This dimmer is also designed for easy installation without a neutral wire, making it ideal for older homes or locations where neutral wiring is not available. With support for single-pole and 3-way configurations, it allows lighting to be controlled from one or two locations, such as staircases, hallways, or large rooms.

Key Features

Smooth & Precise Dimming

• Advanced ELV (Electronic Low Voltage) reverse phase dimming technology.

• Provides gradual brightness adjustment with minimal flicker.

• Large slide control allows accurate lighting level selection.

Convenient Control Design

• Integrated rocker switch for easy on/off operation.

• Slide dimmer enables quick brightness adjustments.

• Wall plate included for a clean and professional appearance.

Wide Compatibility

• Supports up to 250W dimmable LED or CFL lighting.

• Supports up to 300W incandescent lighting.

• Works with AC120V and 277V, 60Hz systems for residential and commercial use.

• Compatible with Shine Decor lighting products including Lum Neon, Eco Neon, COB Neon, COB Strip, ProSelect Strip, and ProSelect Neon.

Flexible Installation Options

• Supports single-pole and 3-way wiring configurations.

• Perfect for controlling lighting from one location or two locations.

• No neutral wire required, simplifying installation in older homes.

Quiet & Reliable Operation

• Trailing-edge dimming technology helps reduce buzzing noise.

• Provides smooth and stable lighting transitions.

Technical Details

The dimmer operates on AC120V or 277V at 60Hz and uses a terminal cap wiring type for secure installation. It supports up to 300W for incandescent lighting and 250W for LED or CFL fixtures. The switch is designed to function in operating temperatures between 23°F and 104°F and is UL Listed, ensuring compliance with safety standards.

Each dimmer switch supports a maximum lighting run length of 65.6 feet. Exceeding this recommended length may cause the dimmer to overheat or become damaged.

Applications

• Residential LED lighting control

• Commercial lighting systems

• LED neon and strip lighting installations

• Staircases, hallways, and multi-location lighting control

• Architectural and accent lighting

Conclusion

The ELV Slide Dimmer Light Switch (UL Listed) provides reliable, smooth dimming performance with flexible installation options. With wide compatibility, quiet operation, and an easy-to-use slide control design, it offers an efficient and professional solution for managing LED and low-voltage lighting in both residential and commercial environments.

Universal Dimmer Controller Pack for 120V LED Strip Lights and Neon Rope Lights

Dimmer User Manual

Compatible Models:

        This dimmer controller is specifically designed for All Lumens Depot original 120V LED strip lights and LED neon rope lights. For neon strips that have been cut, a hard-wired connection is required to use this dimmer remote properly.

Important Warnings:

• Not for Low Voltage Lights: Do not use this dimmer with 12V or 24V neon rope lights, as these models already include a remote control.

• CCT Strip Compatibility: The 120V CCT strip light packs are equipped with an IR remote, so an additional dimmer pack is unnecessary.

Features and Notes:

• Brightness Memory Function: The dimmer retains its last brightness setting, eliminating the need to readjust the brightness each time you power it on.

• Simple Operation: Easy to connect and control, providing seamless dimming functionality for 120V lighting setups.

This universal dimmer is ideal for enhancing the versatility and ambiance of your lighting installations while ensuring compatibility and ease of use.

Lumens Depot: 120V LED Strip Connector Kit

Enhance Your LED Lighting with Our 120V Connector Kit for 10x4.5mm ProSelect Strips
This connector kit is designed to provide an easy and secure connection for your 10x4.5mm Unicolor ProSelect LED strips. With all the necessary components for quick installation, this kit ensures reliable and efficient performance.

When you need to make a jump connection between 2 strip light segments, you can cut the COB neon rope light (the light is cuttable every 4.55cm / 1.8in), then use the 5.9-inch-long connecting wire to connect 2 light strips. Without wiring or soldering, you can use the connecting wires to connect COB neon rope light segments quickly.

Key Features:

• Perfect Fit:

  Compatible with 6x10mm Unicolor LED strips.

• High-Quality Components:

  Built with durable materials for long-lasting connections.

• Easy Installation:

  Includes all necessary components for a hassle-free setup.

• Versatile Use:

  Ideal for connecting LED strips in residential and commercial spaces.

Package Contents for Wire Connector Pack:

• 5 x 5.9Inch connection wires
• 10 x Plastic Connector
  
• 2 x 20in heat shrink tubes
  

Package Contents for clip Connector Pack:

• 5 x connector pins
• 10 x Plastic Connector
  
• 1 x 20in heat shrink tubes
  

Why Choose This Kit?

• Quick & Secure Setup:

  This kit offers everything you need to ensure your 10x4.5mm LED strips are connected properly.

• Durability:

  The heat shrink tubes provide extra protection, ensuring longevity and safety for your lighting system.

• Versatile Use:

  Ideal for creating customized LED lighting displays in homes, offices, or retail spaces.

Elevate Your LED Lighting
With the 120V LED Strip Connector Kit for10x4.5mm ProSelect, enjoy seamless connectivity and durability. Shop now and enhance your lighting setup!

Waterproof End Cap Set for 120V Flexible COB LED Neon Rope Light (10x4.5mm)

This waterproof end cap set is designed specifically for use with 120V Flexible COB LED Neon Rope Lights, ensuring a secure and reliable seal for durability and long-lasting performance. Follow these instructions for proper installation:

Installation Instructions:

1. Prepare the End Cap

• Squeeze a small amount of silicone glue into the end cap.

• Ensure the glue is evenly distributed inside to create a secure and waterproof seal.

2. Attach the LED Strip

• Carefully insert the end of the LED neon rope light into the end cap.

• Press firmly to ensure a snug and proper fit, allowing the silicone glue to adhere fully.

3. Cut the Heat-Shrink Tube

• Measure and cut an appropriate length of heat-shrink tubing to cover the connector area completely.

• Position the heat-shrink tube over the connection point, ensuring it overlaps both the end cap and the LED strip for maximum coverage.

4. Heat the Tube

• Use a heat gun to gently apply heat to the heat-shrink tube.

• Ensure the tube shrinks uniformly around the connector, creating a tight and secure seal.

5. Inspect the Seal

• Double-check the heat-shrink tube to ensure it has fully melted and adhered around the connector area.

• Confirm that the seal is smooth and free of gaps for optimal waterproofing.

Tips for Best Results:

• Always use high-quality silicone glue and heat-shrink tubing for the best waterproof performance.

• Allow sufficient time for the silicone glue to cure completely before exposing the end cap to water or outdoor conditions.

• When using the heat gun, maintain a steady motion to avoid overheating or damaging the tubing.

6FT Extra Power Cord Pack for 120V Flexible COB LED Neon Rope Light – 10x4.5mm Accessory

Enhance your lighting setup with this 6FT Extra Power Cord Pack, specially designed for 120V Flexible COB LED Neon Rope Lights (10x4.5mm). This durable and reliable accessory ensures seamless power connections, enabling you to create stunning lighting designs with ease.

Connecting Method for Power Cord with COB LED Neon Rope Light

1. Prepare Your Tools and Materials:

   • 120V Flexible COB LED Neon Rope Light (10x4.5mm).
   • Power Cord with two-prong connector pin.
   • End Cap to seal the cut end.
   • Heat Shrink Tube for insulation.
   • Scissors or a sharp cutter for trimming.
   • Heat gun or hairdryer for the shrink tube.

2. Cut the Rope Light:

   • Identify the cut marks printed on the COB LED Neon Rope Light.
   • Use scissors to carefully cut the rope light at the designated mark.

3. Insert the Two-Prong Connector Pin:

   • Align the two-prong connector pin with the copper contact points on the cut end of the neon rope light.
   • Gently push the pins into the rope light until they are securely connected.

4. Connect the Power Cord:

   • Attach the power cord to the connector pin by pressing the plug firmly into place.
   • Ensure the connection is snug and secure.

5. Seal the Open End:

   • Place the end cap on the opposite end of the rope light to protect it from dust, moisture, and electrical damage.

6. Apply the Heat Shrink Tube:

   • Slide the heat shrink tube over the connection point between the power cord and the rope light.
   • Use a heat gun or hairdryer to shrink the tube, ensuring a tight and insulated seal.

7. Plug into Power Source:

   • Once connected and sealed, plug the power cord into a standard 120V outlet. Test the rope light to ensure it illuminates properly.

Why Choose This Power Cord Pack?

• Perfect Compatibility: Designed for 120V COB LED Neon Rope Lights with a 10x4.5mm profile.
• Long-Lasting Durability: Built with high-quality materials for reliable and safe operation.
• Easy Installation: No complex tools or wiring required.
• Flexible Length: The 6FT cord provides added flexibility for your lighting projects.

Whether you’re decorating your home, business, or event space, this 6FT Extra Power Cord Pack is the ideal accessory to complete your COB LED Neon Rope Light setup with a professional touch.

Lumens Depot Aluminum Track Channel - 3.3FT/1M (10-Pack)

Enhance your lighting installations with Lumens Depot Aluminum Track Channels, designed specifically for Lumens Depot 10x4.5mm 120V COB LED Rope Lights. This premium accessory ensures durability, ease of use, and a professional finish for your lighting projects.

Key Features

Exclusive Compatibility

• Tailored Design: Only compatible with Lumens Depot 10x4.5mm 120V COB LED Rope Lights. Not suitable for other models.
• Perfect Fit: Guarantees secure and precise installation for seamless lighting.

High-Quality Materials

• Durable & Lightweight: Crafted from rust-free, lightweight metal for long-lasting performance.
• Animal & Plant-Friendly: Silvery gray finish that blends harmoniously with various environments.

Ease of Installation

• Straightforward Mounting: Designed to provide the straightest mounting option for your neon rope lights.
• Complete Set: Comes with all necessary hardware, including screws, for hassle-free setup.

Specifications

• Material: Lightweight, rust-free aluminum.
• Length: Each track measures 3.3FT/1M.
• Pack Size: 10 aluminum tracks included.
• Accessories: 24 screws for secure installation.

Package Includes

• 10 x 3.3FT/1M Aluminum Tracks.
• 24 x Screws.

Why Choose Lumens Depot Aluminum Tracks?

• Professional Results: Achieve clean, straight installations for your COB LED rope lights.
• Durability You Can Trust: Built to withstand various environments without rusting or corroding.
• Customer Support: Reach out with any questions or concerns, and expect a reply within 24 hours.

Ensure your lighting projects are secure, stylish, and professionally installed with Lumens Depot Aluminum Track Channels.

110V LED Neon Lights Mounting Clips Pack – Secure & Effortless Installation for Pro Select, ECO, and LUM Neon Rope Lights

Enhance your neon lighting setup with the Lumens Depot 110V LED Neon Lights Mounting Clips Pack. Designed for easy installation, this high-quality pack is perfect for 7x14.5mm Pro Select, 8x16mm ECO Neon, and LUM Neon Rope Lights, offering a professional and secure fit for your neon lights.

Key Features:

• Premium Quality Materials

  : Crafted from durable, high-quality aluminum for long-lasting stability.

• Effortless Installation

  : Includes 20 aluminum mounting clips and 40 screws for simple, secure setup.

• Versatile Compatibility

  : Compatible with 7x14.5mm Pro Select, 8x16mm ECO, and LUM Neon Rope Lights for a snug fit.

• Sleek Aesthetics

  : Discreet design that blends seamlessly with your neon lights, letting them shine brightly without distractions.

• Perfect for Any Space

  : Ideal for residential and commercial use, from living rooms to businesses, creating the ambiance you desire.

Package Contents:

• 20 Aluminum Mounting Clips
• 40 Screws

Why Choose Our Mounting Clips?

• Secure Fit

  : Designed specifically for popular neon rope light sizes, ensuring a reliable, tight hold.

• Easy Setup

  : Simplifies the process of installing your neon lights for an effortless transformation of any room or space.

• Long-Term Durability

  : Made from high-quality aluminum, these clips will keep your lights in place for years to come.

Elevate your neon lighting with ease – Shop the 110V LED Neon Lights Mounting Clips Pack today and illuminate your world with confidence!